How to Use IJOY CAPO 216 Squonk Mod – User Manual

Thank you for choosing IJOY! Please read this manual to ensure proper use. For more information about this product or use, please consult your dealer or local IJOY visit our website

Product presentation:

CAPO IJOY Squonk box mod 216 is the first and smallest box double Squonk 20700 mod! Long battery life, stylish, personalized shot button and battery cover with a handy adjustable controls lock design, large screen OLED and high power 5-216W adjustable, simple and safe operation. Suitable for RDA with large diameter support USB fast charging. Adopt transparent silicone + ABS combination of hard and soft ecological Squonk special bottle, effectively prevent accidental leakage of compression dismantling! Users can also use the 18650-18650 of the adapter.


1 * 216 IJOY CAPO Squonk BOX MOD

1 * Warranty Card

1 * USB Cable

1 * Manual

• Screen size: 0.66 “0LED.
• Size: 45 * S * 83.S /1.783.292.0 1.25 inches.
• Output Power: 5Watts-216watts
• Output voltage: O.SVolts-8.0Volts.
• Output Current: 1.0A-36A.
• Temperature: 300-600’F / s 150-31 “C.
• The wire control mode Power Resistance Range: 0.06ohm-3.0ohm
• Energy efficiency: 95%.

• Method of Fire: stainless steel metal button drawing.
• Set the feeding method: and down button.
• Upgradeable Firmware: Yes.
• Output mode: / TI / VW mode Ni / SS and special user
• Cell type: IJOY Mystique Tank
20700 High Speed ​​cells (discharge current must be greater than 40A) 18650 high speed cell with the help of battery sleeve (discharge current must be greater than 35A)

Operation instruction:

  1. Batteries lnstalling

Open the battery cover, insert two 20700 batteries into the battery slot, please pay attention to the positive and negative electrodes. You can also use 18650 battery sleeve.

  1. On / Off

Press the shutter button 5 times quickly to turn the unit on and off. After ignition, uoy OLED logo and the version number of the software on standby AGAIN DTL DISPOSABLE

Please adjust the power in an appropriate range to match the aerosol is used before use.
When a new atomizer is connected, please press the “+” key and – for the initial value of the resistance temperature calibration) »»

  1. vaping
    While the power is on, just keep pressing the shutter button of the vaporizer
    (Starting time: 10 seconds)
    While the power is on, the OLED display default display mode VW.
  2. menu

Press the shutter button 3 times in 2 seconds to enter any device menu, then go to the menu operation, the +/- button does not move menu shutter button to confirm.

  1. Mode Temp Ni / Ti / SS
  2. Temperature of the information display screen control mode (work of power, resistance, voltage, operating temperature, and battery power)
  3. Press + and – to increase and decrease, shutter button to confirm, then you can move to adjust the temperature or power Smoant Karat Replacement Pod .
  4. VWMode

The predetermined power is 85 W output power can be adjusted from 5W-216W by pressing the control, +: to increase and decrease.

  1. Setup Mode

In entering this mode, the display NORMA / hard / soft management mode temperature control:

• Normal mode: This is your current power chosen before
• difficult mode: Powerful + 30% before establishing his power.
• The soft mode: setting power of 20% before its power Uwell Caliburn KOKO .

Setting the ECA?

From the main menu, go to the display mode “CRT”, press the button to confirm the fire. Press the left / right keys to select certain parameters.

How to identify the new and the same coil

When removing and reinstalling a way of controlling the temperature of the tank, please press the0-0button to confirm (same coil) if the coil is used above, please press The0 + “to confirm (new coil) if the coil is new Uwell Amulet Replacement

  1. Charging via USB?

When the voltage is less than 3.3 V, the display shows “low battery”, then you need to charge your device, connect the device via the USB cable to the computer or AC adapter. You can not vape for chargin

Leave a Reply

Your email address will not be published. Required fields are marked *