How to Use Joyetech Atopack Dolphin Kit – User Manual

Using Atopack Dolphin
Power on / off: Press the fire button 5 times in quick succession to activate the LED flashes 5 times Smok Vape Pen . Press the fire button the same way, it will be off.

Soak JVIC coil: Remove the JVIC coil and drip a few drops of re-liquid it contains.
E-filling liquid: Open the lid and inject the liquid into e-directly.
Note: Please do not overfill to avoid overflow.
Vaping: Insert JVIC reel in the cartridge. Place the cartridge in the battery. Press the button to inhale, exhale to release.
JVIC coil replacement:
Remove the cartridge and remove the coil JVIC to replace or clean.
(Note: Please do not wash the spray head with water just wipe with a cloth dry cleaning.). Kangvape Vape

Load: Just load the DOLOHIN ATOPACH by connecting it to a computer or a wall adapter via a USB cable. When it is fully charged, the light stays on for 10 seconds and then go out.

Functions:
Short circuit protection:

  1. At short-circuit occurs before operation, the LED blinks 5 times and the coils of the apparatus itself MOTI Piin Vape
  2. When the short circuit occurs during operation, the LED flashes three times and output cuts off automatically.

Protection Spray:
The ATOPACK DOLPHIN has a 10-second run time protection. The light flashes 10 times if the button is pressed the fire for more than 10 seconds.

Low voltage protection:
When the voltage drops of the battery lower than 3.3V, the indicator light flashes 40 times and the apparatus is turned off. Just load to light.

Detection of resistance:

  1. When resistance to the outlet end is> 3ohm, the indicator light flashes slowly if you press the fire button.
  2. When the resistance to the exit end is <0.15ohm, the LED blinks rapidly 5 times, suggesting ohm is a short circuit or low potential.

battery indication:
The light indicates that the life of the battery as follows:

Battery using:

  1. Please use the correct charging equipment from reputable suppliers.
  2. Please put the batteries on a hard surface while charging.
  3. Please turn off the device when it is not used.
  4. Do not let the battery charging unattended.
  5. Do not expose the battery to extreme heat, cold or direct sun light.
  6. Keep away water or other liquid.
  7. MOTI Replacement Pre-filled Pod 1.8ml 3PCs English Edition

Precautions:

  1. Do not use the device in stormy weather or dust state.
  2. Connect the USB port and charger correctly. Unplug the charger when charging is complete.
  3. Do not put the device in your pocket or purse directly; do not mix with coins, jewelry or other hard objects.
  4. The charger and the battery may become warm during charging, keep out of the flammable gas, liquid or other

Warning:

  1. Keep out of reach of children Vaporesso Luxe S 220W
  2. This device is not recommended for children under 18 or non-smoking.
  3. This device is not suitable for use by pregnant or nursing women.
  4. This device is not suitable for use by who are allergic or sensitive to nicotine or those who can not use nicotine products for health reasons.

Warning:

  1. have your device repaired by Joyetech. Do not attempt to repair the unit by yourself as damage or injury can occur
  2. Do not leave the unit in high temperature or humid conditions as this could damage the unit. The proper operating temperature ranges from 0 to 45 ℃ ℃ during loading and -10 ℃ 60 ℃ during use.
  3. Do not try to combine the device with parts other e-cigarette brands. Joyetech will not responsibility and the warranty is void if damage this way.

Warranty conditions:
Please refer to your product warranty card Joyetech. We are not responsible for any damage caused by user error. Our warranty is valid for products purchased from third party suppliers.
Joyrtech agree to provide warranty service under the following conditions:

  1. This warranty provides free repair of the charge for the goods of the band Joyetech defective. The warranty period is 90 days from the date of purchase by

Read More !

Leave a Reply

Your email address will not be published. Required fields are marked *